Scalloped Frame with Butterfly and Flowers and Holiday Sales

Good Tuesday morning.  I have an elegant scalloped frame with butterfly and flowers card to share with you today made using Rubbernecker Stamps and dies and sentiment.  The frame was made using 5119D Nested Circle Scallop with Holes and 5029D Nested Circle Scallop.   The double layered butterfly with flowers was made using 3020D Butterflies are Free, 5147-05D Flower Stems, 5147-09D Flower Buds.  The sentiment is 627-02 Gentle as a Butterfly.  The sentiment and dies are all on 15% off at Rubbernecker’s July 4th holiday sale.

Come see how I made this pretty scalloped frame with butterfly and flowers card.

The Frame and Sentiment

I secured the stamp and cardstock in my MISTI, applied versa and stamped the sentiment.  The clear versa is a little hard to see on white cardstock so I applied more versa to the stamp, stamped it a second time just to make sure I had good ink coverage and then sprinkled with gold embossing powder and heated with my heat gun.

I cut the large white scalloped layer, centering the smaller scalloped die in place and then cutting to create the frame.  I cut a yellow scalloped frame and attached it to the back of the white frame using strips of mounting tape. I applied double stick tape to the back of the frame, attached to the frame and then attached the whole framed sentiment to the yellow card base using double stick tape.  I like adding dimension to my projects so I attached the whole yellow layer and frame to the white card base with pieces of mounting tape. That additional layer of dimension adds lots more interest to the card than if it were attached flat to the base.

Come see how I made this pretty scalloped frame with butterfly and flowers thank you card .

Scalloped Frame with Butterfly and Flowers

I cut several pieces of stems and small white flowers and I formed the flowers using my stylus and molding pad.  I cut the butterfly in yellow and attached the stems and flowers using glossy accents.  When I went to attach the butterfly to the frame I saw that the bottom of the yellow butterfly didn’t show up well against the yellow base layer.  I cut a white butterfly and attached it to the frame and then offset the yellow butterfly and attached it over the white butterfly with glossy accents.  I attached yellow Nuvo Crystal Drops in the flower centers using glossy accents for the finishing touch. 

Come see how I made this pretty scalloped frame with butterfly and flowers card with kindness sentiment.

Rubbernecker Stamps Sale

Rubbernecker 4th sale

Ellen Hutson July 4th Holiday Sale

Ellen 4th sale

Dick Blick Sale

Get 20% Off Blick Orders of $79 or More, and Free Shipping on Orders of $35! Use Promo Code CEPD. Exclusions apply.

dickblick.com

Thanks for coming by today.  I hope you have been inspired to make your own scalloped frame with butterfly and flowers card.  I sure had fun making mine. 

 
Nested Circle Scallop w/ Holes Die…
[ RBB ]
Nested Circle Scallop Die Cut 5029D
[ RBB ]
3020D Butterflies are Free Die set
[ RBB ]
Flower Buds Die Cut 5147-09D
[ RBB ]
Flower Stems Die 5147-05D
[ RBB ]
Gentle As a Butterfly – 627-02
[ RBB ]
Kittie Kraft basics #1
[ RBB ]
Bazzill Card Shoppe Cardstock, Easter…
[ ELH ]
Bazzill Card Shoppe Cardstock, Sour…
[ ELH ]
Neenah Cardstock, Neenah Heavyweight,…
[ ELH ]
Susan’s Garden 4pcs. all metal tool set
[ ELZ | ELH ]
Large Molding Pad (6.5″ X 12″/16.5mm…
[ ELZ ]
VersaMark Ink Pad
[ ELH ]
Ranger Super Fine Embossing Powder, Gold
[ ELH ]
Tonic Nuvo Crystal Drops, Dandelion…
[ ELH ]
My Sweet Petunia MISTI Laser Etched…
[ ELH ]
My Sweet Petunia Mini MISTI Laser…
[ ELH ]
Be Creative Tape, 7mm (3/10″)
[ ELH ]
Be Creative Tape, 15mm (3/5″)
[ ELH ]
Be Creative Tape, 25mm (1″)
[ ELH ]
Be Creative Tape, 5mm (1/4″)
[ ELH ]
Be Creative Tape, 3mm (1/8″)
[ ELH ]
EK Tools, Precision 5 Inch Scissors…
[ ELH ]
Ranger Non-Stick Craft Sheet
[ ELH ]
Glue Dots, 3/8″ (4029)
[ ELH ]
Glue Dots, Mini (3/16″)
[ ELH ]
Glue Dots, Micro (1/8″)
[ ELH ]
Scotch Foam Mounting Tape
[ ELH ]
ATG Double-Sided Refill Tape, 2 pk, 1/4″
[ ELH ]
ATG Kit, Advanced Tape Glider
[ ELH ]
Ranger Accents, Mini Glossy Accents
[ ELH ]
Ranger Accents, Glossy Accents
[ ELH ]
Creative Expressions Cosmic Shimmer…
[ ELH ]
Crafter’s Pick The Ultimate Glue, 4 oz.
[ ELH ]
Hero Arts Embossing Gun (Wagner)
[ ELH ]
Tonic Maxi 12 Inch Guillotine Paper…
[ ELH ]
Teflon Bone Folder
[ ELH ]
Tonic Comfort 8.5 Inch Guillotine…
[ ELH ]
Scor-Pal Measuring & Scoring Board 12×12
[ ELH ]
Scor-Pal Glitter Clean-Up Cloth
[ ELH ]
Memory Box Dies, Metal Adaptor Plate
[ ELH ]
Sizzix Accessory – Standard Magnetic…
[ SZZ | SBC ]
Sizzix Accessory – Precision Base…
[ SZZ | SBC ]
Sizzix Big Shot White & Gray
[ ELH | SZZ | SBC ]
Dremel 7700-1/15 MultiPro 7.2-Volt…
[ AMZUS ]
 

Die Cut Butterfly, Flowers and Scallop Layer

Good Tuesday morning.  I have one more die cut butterfly, flowers and scallop layer card to share with you today. I most likely will put the butterfly dies away for a little rest as I have made so many cards using them recently but I just can’t seem to help myself.  I think they are so pretty and look great on a clean white background.  I couldn’t resist adding two small purple strips to the scallop layer for another element of dimension and interest. 

For this project I used Rubbernecker Stamps 5141D Nested Rectangle Scallop w/Holes, 5102D 2 Part Butterfly #3, 5147-09D Flower Buds and 5147-05D Flower Stems.

Check out how I made this elegant die cut butterfly, flowers and scallop layer card.

The Scallop Layer and Strips

I cut the purple layer and attached it to the white card base using strips of mounting tape.  I cut the white scallop layer, applied mounting tape to the back of it and attached it to the purple base layer.  I cut a partial portion of the scallop die using the purple cardstock and cut the strips and attached them to the white scallop layer using double stick tape.

The Butterfly and Flowers

I cut the solid butterfly in purple and the decorative butterfly layer in white.  I attached the two pieces together using glossy accents.  I cut purple flowers and formed them using my stylus and molding pad.  I cut the foliage and formed them gently with my fingers.  I attached three main foliage layers to the center of the butterflies using glossy accent to create a base for the flowers.  I attached several flowers using glossy accents and then tucked a few more pieces of foliage to the arrangement to finish. 

Check out how I made this clean and simple die cut butterfly, flowers and scallop layer project.

Assembling the Die Cut Butterfly, Flowers and Scallop Layer

I attached the butterfly to the scalloped layer with a piece of mounting tape. I finished by attaching small pre made white Nuvo Crystal Drops to the flower centers using glossy accents.

Check out how I made this clean and simple die cut butterfly, flowers and scallop layer card.

I love playing with the die cut butterfly, flowers and scallop layer and think this is such an elegant combination for a card.  It is so versatile and could be used for so many occasions.  I hope you haven’t tired of seeing so many projects made using one of my favorite color combination for summer cards. You can check out this butterfly link if you are interested in seeing more butterfly projects I’ve made recently.

 
Nested Rectangle Scallop w/ Holes 5141D
[ RBB ]
5102D 2 Part Butterfly #3
[ RBB ]
Flower Buds Die Cut 5147-09D
[ RBB ]
Flower Stems Die 5147-05D
[ RBB ]
Kittie Kraft basics #1
[ RBB ]
Bazzill Card Shoppe Cardstock, Easter…
[ ELH ]
Bazzill Card Shoppe Cardstock, Sour…
[ ELH ]
Neenah Cardstock, Neenah Heavyweight,…
[ ELH ]
Susan’s Garden 4pcs. all metal tool set
[ ELZ | ELH ]
Large Molding Pad (6.5″ X 12″/16.5mm…
[ ELZ ]
Tonic Nuvo Crystal Drops, Gloss White
[ ELH ]
My Sweet Petunia MISTI Laser Etched…
[ ELH ]
My Sweet Petunia Mini MISTI Laser…
[ ELH ]
Be Creative Tape, 7mm (3/10″)
[ ELH ]
Be Creative Tape, 15mm (3/5″)
[ ELH ]
Be Creative Tape, 25mm (1″)
[ ELH ]
Be Creative Tape, 5mm (1/4″)
[ ELH ]
Be Creative Tape, 3mm (1/8″)
[ ELH ]
EK Tools, Precision 5 Inch Scissors…
[ ELH ]
Ranger Non-Stick Craft Sheet
[ ELH ]
Glue Dots, 3/8″ (4029)
[ ELH ]
Glue Dots, Mini (3/16″)
[ ELH ]
Glue Dots, Micro (1/8″)
[ ELH ]
Scotch Foam Mounting Tape
[ ELH ]
ATG Double-Sided Refill Tape, 2 pk, 1/4″
[ ELH ]
ATG Kit, Advanced Tape Glider
[ ELH ]
Ranger Accents, Mini Glossy Accents
[ ELH ]
Ranger Accents, Glossy Accents
[ ELH ]
Creative Expressions Cosmic Shimmer…
[ ELH ]
Crafter’s Pick The Ultimate Glue, 4 oz.
[ ELH ]
Hero Arts Embossing Gun (Wagner)
[ ELH ]
Tonic Maxi 12 Inch Guillotine Paper…
[ ELH ]
Teflon Bone Folder
[ ELH ]
Tonic Comfort 8.5 Inch Guillotine…
[ ELH ]
Scor-Pal Measuring & Scoring Board 12×12
[ ELH ]
Scor-Pal Glitter Clean-Up Cloth
[ ELH ]
Memory Box Dies, Metal Adaptor Plate
[ ELH ]
Sizzix Accessory – Standard Magnetic…
[ SZZ | SBC ]
Sizzix Accessory – Precision Base…
[ SZZ | SBC ]
Sizzix Big Shot White & Gray
[ ELH | SZZ | SBC ]
Dremel 7700-1/15 MultiPro 7.2-Volt…
[ AMZUS ]
 

Lattice and Butterfly with Flowers

Good Friday morning.  I have an elegant lattice and butterfly with flowers card to share with you today made using dies by Rubbernecker Stamps.  I used the 5132D Rectangle Combo #2 OPC die to frame the 5026D Circle Lattice layer and used the 5028D Nested Rectangle Scallop die to create the background layer.  The butterfly was made using the 947-01B 2 Part Butterfly and the flowers were made using the 5109D Mixable Flower Stack and 5147-10 Tiny Flower Buds and the foliage was made using 5118D Leaf Group.

Come see how I made this elegant lattice and butterfly with flowers card.

The Lattice and Frame

I lined up the circle lattice die on my cardstock and cut.  I lined it up against the first cut and cut a second time.  I wanted the lattice background to be large enough to fit in behind the scalloped frame.  I measured and cut the lattice and attached to the back of the frame using double stick tape.  I applied thin strips of mounting tape to the back of the framed lattice and attached it to the pink scalloped layer.  I applied another layer of mounting tape to the back of the pink layer and attached it to the white card base.

Come see how I made this lovely lattice and butterfly with flowers card.

Lattice and Butterfly with Flowers

I cut the pink and white butterflies, applied glossy accents to the body portion of the white butterfly and attached it to the pink butterfly.  Next I applied mounting tape to the back of the butterfly and attached it to the lattice layer.  I cut one section of the flower layers, formed them with my stylus and molding pad and attached the sections together using glossy accents.  I cut a couple sections of the leaf group and cut the branches apart.  I created a foliage base on the back of the butterfly by attaching a few branches using glossy accents.  The large flower was attached to the foliage base with glossy accents and then I tucked several more branches under and around the flower and butterfly to fill in the arrangement.  I formed tiny flowers using my stylus and molding pad and attached the flowers all around the foliage using glossy accents.  I attached one pre made white Nuvo Crystal Drop in the center of the large flower to finish.

Come see how I made this pretty lattice and butterfly with flowers card.

Thank you for coming by today.  I hope you have time this weekend to get your dies and punches out to create your own lattice and butterfly with flowers project.

 
Rectangle Combo #2 OPC Die 5132D
[ RBB ]
Nested Rectangle Scallop Die Cut 5028D
[ RBB ]
Circle Lattice Die Cut 5026D
[ RBB ]
2 Part Butterfly #2 947-01B
[ RBB ]
Mixable Flower Stack Die 5109D
[ RBB ]
Leaf Group die 5118D
[ RBB ]
Tiny Flower Buds Die Cut 5147-10D
[ RBB ]
Kittie Kraft basics #1
[ RBB ]
Bazzill Card Shoppe Cardstock, Easter…
[ ELH ]
Bazzill Card Shoppe Cardstock,…
[ ELH ]
Neenah Cardstock, Neenah Heavyweight,…
[ ELH ]
Tonic Nuvo Crystal Drops, Gloss White
[ ELH | MFT ]
Susan’s Garden 4pcs. all metal tool set
[ ELZ | ELH ]
Large Molding Pad (6.5″ X 12″/16.5mm…
[ ELZ ]
My Sweet Petunia MISTI Laser Etched…
[ ELH ]
My Sweet Petunia Mini MISTI Laser…
[ ELH ]
Be Creative Tape, 7mm (3/10″)
[ ELH ]
Be Creative Tape, 15mm (3/5″)
[ ELH ]
Be Creative Tape, 25mm (1″)
[ ELH ]
Be Creative Tape, 5mm (1/4″)
[ ELH ]
Be Creative Tape, 3mm (1/8″)
[ ELH ]
EK Tools, Precision 5 Inch Scissors…
[ ELH ]
Ranger Non-Stick Craft Sheet
[ ELH ]
Glue Dots, 3/8″ (4029)
[ ELH ]
Glue Dots, Mini (3/16″)
[ ELH ]
Glue Dots, Micro (1/8″)
[ ELH ]
Scotch Foam Mounting Tape
[ ELH ]
ATG Double-Sided Refill Tape, 2 pk, 1/4″
[ ELH ]
ATG Kit, Advanced Tape Glider
[ ELH ]
Ranger Accents, Mini Glossy Accents
[ ELH ]
Ranger Accents, Glossy Accents
[ ELH ]
Creative Expressions Cosmic Shimmer…
[ ELH ]
Crafter’s Pick The Ultimate Glue, 4 oz.
[ ELH ]
PanPastel Sofft Mini Applicators, 12 pk
[ ELH ]
Hero Arts Embossing Gun (Wagner)
[ ELH ]
Tonic Maxi 12 Inch Guillotine Paper…
[ ELH ]
Teflon Bone Folder
[ ELH ]
Tonic Comfort 8.5 Inch Guillotine…
[ ELH ]
Scor-Pal Measuring & Scoring Board 12×12
[ ELH ]
Scor-Pal Glitter Clean-Up Cloth
[ ELH ]
Memory Box Dies, Metal Adaptor Plate
[ ELH ]
Sizzix Accessory – Standard Magnetic…
[ SZZ | SBC ]
Sizzix Accessory – Precision Base…
[ SZZ | SBC ]
Sizzix Big Shot White & Gray
[ ELH | SZZ | SBC ]
Dremel 7700-1/15 MultiPro 7.2-Volt…
[ AMZUS ]
 

Die Cut Lattice and Butterfly Card for DTGD Day 4

My project today is a die cut lattice and butterfly card made for Dare To Get Dirty Day 4 of the Splitcoaststampers Dare To Get Dirty week long challenge event. This event is a special thank you to all of the fan club members who support the site all year long. Have you had a desire to be on the Dirty Dozen design team? This special week of challenges will give you tons of opportunity to be inspired and to show off your wonderful and creative projects right along with the current Dirty Dozen team as well as the alumni team members.  Are you a member of the Splitcoaststampers Fan Club? If not go here to check out all the benefits of being a member. If you are a member hop right on over the special challenge forum here.

Come see how I made this clean and simple die cut lattice and butterfly card.

The Stenciled Pattern

I don’t often use a stenciling technique but thought it would be fun to see if I could use the lattice die cut to create a nice pattern.  I cut the Circle Lattice Die using a 4.5″ piece of scratch cardstock. The die is only two inches wide and I wanted to double the size so I line the die up along the first cut line and cut a second time to create a 4″ square die cut.  I placed the die cut lattice over a piece of white cardstock to use as a stencil and secured in place using painter’s tape.  Next, I used a stylus tool and foam tip along with Tumbled Glass ink to create the lattice pattern on the cardstock layer.  Once I was finished I heat set the ink with my heat gun. 

The Frame

I cut a Square Combo frame using the patterned cardstock and cut a second frame using white cardstock.  I turned the white and patterned frame layers face down and attached them all together using double stick tape.  Next, I applied strips of mounting tape to the back of the frame and attached it to the 5″ square card base.

Come see how I made this simple die cut lattice and butterfly card.

The Butterfly and Flowers

I cut both sections of the 2 Part Butterfly #2 using white cardstock.  Next, I applied Tumbled Glass to the base butterfly using the stylus and foam tip.  I applied the blue ink to a scratch piece of white cardstock and cut tiny flowers using the Flower Buds die.  I cut several pieces of Flower Stems to use along with the flowers to embellish the butterfly.  I used my molding pad and stylus to form the tiny flowers.

Die Cut Lattice and Butterfly Card

I attached the white decorative layer of the butterfly to the blue base using glossy accents.  Next, I attached white flower stems to the butterfly using glossy accents to create a base for the flowers.  I used glossy accents to attach flowers and then attached the whole embellished butterfly to the lattice frame using a piece of mounting tape.  I finished by applying small dots of glossy accents to the flower centers and attaching white pre made Nuvo Crystal Drops.

Come see how I made this bright die cut lattice and butterfly card.

I hope you enjoyed seeing my die cut lattice and butterfly card.  It was lots of fun creating my lattice stenciled frame to match the lattice die cut and I have been inspired with lots of ideas for using some of my other dies to create stencils for future projects.  Thanks for coming by and I hope you have a great day.

 
Square Combo #1 OPC Die 5131D
[ RBB ]
Circle Lattice Die Cut 5026D
[ RBB ]
2 Part Butterfly #2 947-01B
[ RBB ]
Flower Buds Die Cut 5147-09D
[ RBB ]
Flower Stems Die 5147-05D
[ RBB ]
Kittie Kraft basics #1
[ RBB ]
Ranger Distress Ink Pad, Tumbled Glass
[ ELH ]
Neenah Cardstock, Neenah Heavyweight,…
[ ELH ]
Scotch Safe-Release Masking Painter’s…
[ ELH ]
ColorToolBox Stylus Handles 3/Pkg-
[ AMZUS ]
ColorToolBox Stylus Blender Tips…
[ AMZUS ]
Tonic Nuvo Crystal Drops, Gloss White
[ ELH | MFT ]
Susan’s Garden 4pcs. all metal tool set
[ ELZ | ELH ]
Large Molding Pad (6.5″ X 12″/16.5mm…
[ ELZ ]
My Sweet Petunia MISTI Laser Etched…
[ ELH ]
My Sweet Petunia Mini MISTI Laser…
[ ELH ]
Be Creative Tape, 7mm (3/10″)
[ ELH ]
Be Creative Tape, 15mm (3/5″)
[ ELH ]
Be Creative Tape, 25mm (1″)
[ ELH ]
Be Creative Tape, 5mm (1/4″)
[ ELH ]
Be Creative Tape, 3mm (1/8″)
[ ELH ]
EK Tools, Precision 5 Inch Scissors…
[ ELH ]
Ranger Non-Stick Craft Sheet
[ ELH ]
Glue Dots, 3/8″ (4029)
[ ELH ]
Glue Dots, Mini (3/16″)
[ ELH ]
Glue Dots, Micro (1/8″)
[ ELH ]
Scotch Foam Mounting Tape
[ ELH ]
ATG Double-Sided Refill Tape, 2 pk, 1/4″
[ ELH ]
ATG Kit, Advanced Tape Glider
[ ELH ]
Ranger Accents, Mini Glossy Accents
[ ELH ]
Ranger Accents, Glossy Accents
[ ELH ]
Creative Expressions Cosmic Shimmer…
[ ELH ]
Crafter’s Pick The Ultimate Glue, 4 oz.
[ ELH ]
PanPastel Sofft Mini Applicators, 12 pk
[ ELH ]
Hero Arts Embossing Gun (Wagner)
[ ELH ]
Tonic Maxi 12 Inch Guillotine Paper…
[ ELH ]
Teflon Bone Folder
[ ELH ]
Tonic Comfort 8.5 Inch Guillotine…
[ ELH ]
Scor-Pal Measuring & Scoring Board 12×12
[ ELH ]
Scor-Pal Glitter Clean-Up Cloth
[ ELH ]
Memory Box Dies, Metal Adaptor Plate
[ ELH ]
Sizzix Accessory – Standard Magnetic…
[ SZZ | SBC ]
Sizzix Accessory – Precision Base…
[ SZZ | SBC ]
Sizzix Big Shot White & Gray
[ ELH | SZZ | SBC ]
Dremel 7700-1/15 MultiPro 7.2-Volt…
[ AMZUS ]
 

Circle Framed Die Cut Butterfly

Good Monday morning.  My project today is a circle framed die cut butterfly card made using the Rubbernecker Nested Circle X Stitch set, 2 Part Butterfly # 1, Flower Buds, Flower Stems and French Script Background.  I’ve had the French Script Background and Nested Circle X Stitch for a while but this is my first time using them.  I thought the soft blue script looked pretty as a background for the decorative butterfly and the X stitch pattern on the frame adds another element of interest.

Come see how I made this pretty circle framed die cut butterfly card with a French script background and tiny flowers.

The French Script Background and Frame

I secured the large background stamp and cardstock in my MISTI, applied the Baby Blue ink to the stamp and stamped the image.  Next, I cut the stamped image layer to 4.25″ ti fit on the 4.50″ blue layer.  I applied mounting tape to the back of the blue layer and attached it to the card base.

The frame was cut using the two largest frames in the set.  I used my magnetic platform to secure the dies in place on the cardstock and cut.  I applied thin strips of mounting tape to the back of the frame and attached it to the script layer.

Come see how I made this elegant circle framed die cut butterfly card with tiny flowers and a French script background.

The Butterfly and Flowers

I cut the butterfly sections and attached them together using glossy accents.  I formed the flower buds using my stylus and molding pad.  Next, I attached pieces of the flower stems to the base of the butterfly using glossy accents.  I attached several flowers to the stems in a cluster using glossy accents.  The butterfly was attached to the card base using a piece of mounting tape. 

Come see how I made this elegant circle framed die cut butterfly card with a French script background and tiny flowers.

I think the circle framed die cut butterfly card is so pretty and elegant.  Thank you for coming by and I hope you enjoyed seeing my project and that you have a great day.

 
Nested Circle X Stitch 5144-01D
[ RBB ]
2 Part Butterfly #1 946-01D
[ RBB ]
French Script Background – 448
[ RBB ]
Flower Buds Die Cut 5147-09D
[ RBB ]
Flower Stems Die 5147-05D
[ RBB ]
Kittie Kraft basics #1
[ RBB ]
Neenah Cardstock, Neenah Heavyweight,…
[ ELH ]
Bazzill Card Shoppe Cardstock, Icy…
[ ELH ]
Impression Obsession Rubber Stamps…
[ IST ]
Susan’s Garden 4pcs. all metal tool set
[ ELZ | ELH ]
Large Molding Pad (6.5″ X 12″/16.5mm…
[ ELZ ]
My Sweet Petunia MISTI Laser Etched…
[ ELH ]
My Sweet Petunia Mini MISTI Laser…
[ ELH ]
Be Creative Tape, 7mm (3/10″)
[ ELH ]
Be Creative Tape, 15mm (3/5″)
[ ELH ]
Be Creative Tape, 25mm (1″)
[ ELH ]
Be Creative Tape, 5mm (1/4″)
[ ELH ]
Be Creative Tape, 3mm (1/8″)
[ ELH ]
EK Tools, Precision 5 Inch Scissors…
[ ELH ]
Ranger Non-Stick Craft Sheet
[ ELH ]
Glue Dots, 3/8″ (4029)
[ ELH ]
Glue Dots, Mini (3/16″)
[ ELH ]
Glue Dots, Micro (1/8″)
[ ELH ]
Scotch Foam Mounting Tape
[ ELH ]
ATG Double-Sided Refill Tape, 2 pk, 1/4″
[ ELH ]
ATG Kit, Advanced Tape Glider
[ ELH ]
Ranger Accents, Mini Glossy Accents
[ ELH ]
Ranger Accents, Glossy Accents
[ ELH ]
Creative Expressions Cosmic Shimmer…
[ ELH ]
Crafter’s Pick The Ultimate Glue, 4 oz.
[ ELH ]
PanPastel Sofft Mini Applicators, 12 pk
[ ELH ]
Hero Arts Embossing Gun (Wagner)
[ ELH ]
Tonic Maxi 12 Inch Guillotine Paper…
[ ELH ]
Teflon Bone Folder
[ ELH ]
Tonic Comfort 8.5 Inch Guillotine…
[ ELH ]
Scor-Pal Measuring & Scoring Board 12×12
[ ELH ]
Scor-Pal Glitter Clean-Up Cloth
[ ELH ]
Memory Box Dies, Metal Adaptor Plate
[ ELH ]
Sizzix Accessory – Standard Magnetic…
[ SZZ | SBC ]
Sizzix Accessory – Precision Base…
[ SZZ | SBC ]
Sizzix Big Shot White & Gray
[ ELH | SZZ | SBC ]
Dremel 7700-1/15 MultiPro 7.2-Volt…
[ AMZUS ]